What did you do to your Integra Type S today? 🙋🏻‍♂️

[Tw1stedlog1k]

Which model had the black vent arms? I know the dials came on the accord.

Thanks!

Black dials are off of the Accord and HRV (cheaper to buy used)
The vent arms are off of the CRV (much cheaper to buy new)

P/Ns below for the vents (you scavenge them for the arms)
(2x) 776133a0a01za (passenger's side vent), these are cheaper individually but require a little more work to get the arms swapped
(1x) 772453a0a01za (center vents, pair), these are a little more expensive overall but easier to swap out without having to swap arms, you can swap the entire center vent assemblies. Still need to swap out the arms for the driver's and passenger's side.

You could also just get 4 of the passenger's side vents and swap out all the arms if you're on super tight budget but the savings is only about $5 overall. Better to get the center vents and 2 side vents.

I'm working on a replacement for the volume knob but I haven't come across an all black knob that would work yet.

Sponsored

 

[wontondon]

Black dials are off of the Accord and HRV (cheaper to buy used)
The vent arms are off of the CRV (much cheaper to buy new)

P/Ns below for the vent arms
(2x) 776133a0a01za (passenger's side vent), these are cheaper individually but require a little more work to get the arms swapped
or
(1x) 772453a0a01za (center vents, pair), these are a little more expensive overall but easier to swap out without having to swap arms, you can swap the entire center vent assemblies. Still need to swap out the arms for the driver's and passenger's side.

You could also just get 4 of the passenger's side vents and swap out all the arms if you're on super tight budget but the savings is only about $5 overall. Better to get the center vents and 2 side vents.

I'm working on a replacement for the volume knob but I haven't come across an all black knob that would work yet.

Would you happen to have the OEM passenger side vent part no? I snapped mine off taking it apart.

 

[Tw1stedlog1k]

Would you happen to have the OEM passenger side vent part no? I snapped mine off taking it apart.

I think you're looking for this?

https://dreamshop.honda.com/s/category/acura/0ZG6g0000004HomGAE

Outlet Assy., Passenger *NH900L*(NEUTRAL BLACK)
Part Number: 77613-3S5-A01ZA
MSRP : $35.75

 

[Integra23]

Rear SPC camber arms installed.. alignment scheduled in a week or so to pull some camber out. Job took about 2 hours and driver side was fun to do. I used a gear wrench set similar to this, only needed 17mm. https://www.homedepot.com/p/GEARWRE...et-Mechanics-Tool-Set-21-Piece-8921/202330496

This had a slightly lower profile than a standard socket wrench.

 

[Tw1stedlog1k]

I have my Eibach arms (same thing as the SPC just a different paint job) in the box ready to go on. I'm contemplating if I want to do it or pay a shop to do it because I also have a rear sway and end links to go on as well.

2 hours isn't bad but anytime something becomes "fun" I consider what else I could be doing instead...

 

[Integra23]

I have my Eibach arms (same thing as the SPC just a different paint job) in the box ready to go on. I'm contemplating if I want to do it or pay a shop to do it because I also have a rear sway and end links to go on as well.

2 hours isn't bad but anytime something becomes "fun" I consider what else I could be doing instead...

Yeah. I almost had someone else do it because it looked like a pain. I probably could have finished faster if I grabbed all my tools to start.
Driver side I could only hold the bolt with 2 fingers to get it back in and align it. I taped the bolt to my fingers because it kept slipping back.. ?

 

[Westhaver]

Black dials are off of the Accord and HRV (cheaper to buy used)
The vent arms are off of the CRV (much cheaper to buy new)

P/Ns below for the vents (you scavenge them for the arms)
(2x) 776133a0a01za (passenger's side vent), these are cheaper individually but require a little more work to get the arms swapped
(1x) 772453a0a01za (center vents, pair), these are a little more expensive overall but easier to swap out without having to swap arms, you can swap the entire center vent assemblies. Still need to swap out the arms for the driver's and passenger's side.

You could also just get 4 of the passenger's side vents and swap out all the arms if you're on super tight budget but the savings is only about $5 overall. Better to get the center vents and 2 side vents.

I'm working on a replacement for the volume knob but I haven't come across an all black knob that would work yet.

This is super helpful, thank you!

 

[crepr12]

First serious detail in a few months

 

[Victorofhavoc]

First serious detail in a few months

Do I spy godzilla lurking in the reflections? ?

 

[MNTeggy]

A couple recent additions:

Red S on the shifter

Type S valve caps

 

[Old_Dad_Actual]

Did the red S on the console the other day. New Billetworkz shifter knob was installed today. Shipping was stupid fast for a custom order, got it today after ordering on Wednesday night. The engraving is pretty shallow, but that might be for comfort.

The shift boot gave me some issues initially, but a small flathead and some finesse got it off eventually with no damage. I’m liking the additional girth on the knob, though it probably weighs a little less than stock.

 

[mopar_man]

That looks really cool.

 

[SilverRocket]

Did the red S on the console the other day. New Billetworkz shifter knob was installed today. Shipping was stupid fast for a custom order, got it today after ordering on Wednesday night. The engraving is pretty shallow, but that might be for comfort.

The shift boot gave me some issues initially, but a small flathead and some finesse got it off eventually with no damage. I’m liking the additional girth on the knob, though it probably weighs a little less than stock.

That is awesome and the red with black streaks... Chef kiss.

Also me according to your shifter...

 

[Old_Dad_Actual]

That is awesome and the red with black streaks... Chef kiss.

Also me according to your shifter...

It’s particularly funny since I took the interstate with my wife for the first time the other day, and we both commented on how easy and quick it was to be well into prison speeds and not even realize it…

 

[MPMB]

I really love the look of our stock wheels, but have just never been a dark/black wheel guy. While the stocks are off the car for the Chicago winter (which never really materialized), I took the opportunity to have them painted. Looking forward to putting these on soon!

Sponsored