Auto Folding Mirrors installed

[Integra23]

Does this install retain the blind spot warning light on the mirror itself?

Yes, heated mirrors and blind spot functions are retained.

Sponsored

 

[Integra23]

Anyone install Kit F?

Same as Kit C just without a few wires that you don't use.

 

[Ataricade]

Got it. Thank you. So with that do you need to order the mirror covers as well as the mirror turn signals?

the tech already has turn signals so you don’t need either.

if you are adding turn signals on a lower trim you would need a new cover. Make sure you order the right kit for your trim.

 

[Integra23]

Got it. Thank you. So with that do you need to order the mirror covers as well as the mirror turn signals?

Oh. Like mentioned above. I am assuming you have Advanced Tech package. If you already have blinkers in mirror then you can reuse your covers.
If you don't have blinkers in the mirrors currently you may have to get a different kit.

 

[Integra23]

Does the ITS have the turn signals already in the mirror? I have literally never noticed that. Sorry for my ignorance.

Yes. For the ITS either Kit C or F will work. You can reuse your mirror caps.

 

[acurax]

Just completed the install of the model F kit. I followed the Civic SI installation instructions and only the steps for the grey, black, and green wires. I decided to swap the entire base as it seemed like my original color matched Type-S base covers wouldn't fit. This was a bit of a hassle due to the need to de-pin/re-pin the connectors. Which I found went more smoothly inserting a thin, straightened out paper clip in the side of connector where the wire is inserted and then gently pulling the wire out, which also pulled out the paper clip along with it. The de-pinner included with the kit was hit or miss using it form the other side of the connector and couldn't be used on the wire side. Here area few pictures of the differences between the bases, my original is on the left in each image.

 

[Compromise]

I just finished the F Kit install. The roll down function still works, but I cannot seem to get the roll up function when holding the door lock button to work. Any insight into how to make that work? Or is this just not a function of the F Kit? Thank you.

Did you get this too?

https://mikstoreph.com/products/civ...2&_sid=e7d937253&_ss=r&variant=42826719592698

Need this for lock to roll-up.

 

[Integra23]

I just finished the F Kit install. The roll down function still works, but I cannot seem to get the roll up function when holding the door lock button to work. Any insight into how to make that work? Or is this just not a function of the F Kit? Thank you.

Yeah you need to buy that function.
My issue is with the mirrors set to auto-fold the windows roll-up. I reached out to Mik about it and there's nothing you can do.

 

[Integra23]

The windows roll up when? Whenever you lock the car?

Yeah. If you have the mirrors set to auto-fold and the car set to auto-lock when you leave your vehicle the mirrors will fold and doing so causes the windows to close.

 

[Integra23]

Anyone else who did the install have driver side mirror rattle? I tightened everything down real well which solved it for the passenger side, but there’s still a bit of mirror rattle driving at highway speeds on the driver side.

No issues on mine

 

[acurax]

Anyone else who did the install have driver side mirror rattle? I tightened everything down real well which solved it for the passenger side, but there’s still a bit of mirror rattle driving at highway speeds on the driver side.

Yeah, my driver's side mirror glass vibrates at highway speeds, but it doesn't make a rattling sound.

 

[Big Duck]

I’ve started working on the install and im trying to get a grasp on the wiring setup before taking anything apart. Theres not much documentation on the orange wire bundle on the “F” kit, does the setup I have in the photo look correct?

 

[Integra23]

I’ve started working on the install and im trying to get a grasp on the wiring setup before taking anything apart. Theres not much documentation on the orange wire bundle on the “F” kit, does the setup I have in the photo look correct?

Yeah looks correct. It's just a passthrough with a power take off for that module that plugs in. I added instructions to my first post on changing the settings after you install it. By default the horn beeps or something when you lock the door.

 

[Big Duck]

I added instructions to my first post on changing the settings after you install it

when you say settings, are you talking about these buttons?

 

[Integra23]

when you say settings, are you talking about these buttons?

No. Sequence of button pushing. See below.

Sponsored