Auto Folding Mirrors installed

[Big Duck]

I didn't use mine. I need to hunt for it and will let you know.

I reached out to mikstore about it and they're going to send the missing peices to me! Thank you for the offer anyways

Sponsored

 

[MacKharoni]

Anyone having issue with the passenger window not rolling down from the driver side?

When I put back my original window module on the passenger (none folded chip). I was able to control it from driver side fine. Once I put on the mikshop (folded chip) it won't roll down the window.

Updated:
After driving for 40mins the window start working ?‍

 

[Integra23]

Anyone having issue with the passenger window not rolling down from the driver side?

When I put back my original window module on the passenger (none folded chip). I was able to control it from driver side fine. Once I put on the mikshop (folded chip) it won't roll down the window.

Updated:
After driving for 40mins the window start working ?‍

Glad you got it working. I have never had an issue.

 

[dkny008]

Just wondering how you can added " Auto folding door mirrors" into the menu?
Thanks

 

[Compromise]

Just wondering how you can added " Auto folding door mirrors" into the menu?
Thanks

Once the kit is installed, the option shows up by itself.

 

[Wolfman]

Do the mirrors happen to change when you put the car on reverse and angle downward or nah?

 

[Integra23]

Do the mirrors happen to change when you put the car on reverse and angle downward or nah?

This kit does not include tilting. MIk does sell it as a separate kit.

 

[duckies]

@Integra23 Would you happen to know if we can install both the folding and reverse downward tilt at the same time?

 

[Integra23]

@Integra23 Would you happen to know if we can install both the folding and reverse downward tilt at the same time?

The tilt kit is its own unit and seems to be plug-in play. I wouldn't think the two would interfere with each other.
I personally didnt care for this feature kn my Aspec since it seemed to lower the mirror a bit too much. Also over time it wouldnt fully return to the normal set position requiring mirror adjustment every other week.

https://mikstoreph.com/products/civic-2022-side-mirror-reverse-auto-tilting

 

[wickedgoodheah]

Yep. Those are the locks. You pop that before removing the pins

I put two in the wrong hole like a dope and I absolutely cannot figure out how to remove the wires. Tried the unlock on the gray plug with the black lock (it doesn’t unlock very far) and then I tried a tiny paper clip from the front and rear without success. WTF am I trying to accomplish?

 

[Integra23]

I put two in the wrong hole like a dope and I absolutely cannot figure out how to remove the wires. Tried the unlock on the gray plug with the black lock (it doesn’t unlock very far) and then I tried a tiny paper clip from the front and rear without success. WTF am I trying to accomplish?

It happens. I took photos before I disassembled.
You go through the pin side ,there's a slot.
I used a sewing needle to go in and pull that tab out

 

[wickedgoodheah]

It happens. I took photos before I disassembled.
You go through the pin side ,there's a slot.
I used a sewing needle to go in and pull that tab out

I figured it out. Pin side with a sewing needing. My trick was I needed to push the wire all the way in, hold it in place while I got the needle under the clasp (easier said than done) and then once the clasp was released I could pull the wire out. If the wire was too far out (often pushed back by the needle) it was putting pressure on the clasp and I could not release it.

 

[Fish Hunter]

The tilt kit is its own unit and seems to be plug-in play. I wouldn't think the two would interfere with each other.
I personally didnt care for this feature kn my Aspec since it seemed to lower the mirror a bit too much. Also over time it wouldnt fully return to the normal set position requiring mirror adjustment every other week.

https://mikstoreph.com/products/civic-2022-side-mirror-reverse-auto-tilting

Thank you for all the helpful information. I have a 24 ITS. Can I still remove the side mirror covers with the carbon fiber side mirror accessory?
Does anyone know?

I’m also a little confused if I should consider the C or F kit for the ITS? I read a post on this thread a ITS owner bought a F kit and was missing a wire harness?

Thanks again (OG and contributors) for this thread.
Fish

 

[Integra23]

Thank you for all the helpful information. I have a 24 ITS. Can I still remove the side mirror covers with the carbon fiber side mirror accessory?
Does anyone know?

I’m also a little confused if I should consider the C or F kit for the ITS? I read a post on this thread a ITS owner bought a F kit and was missing a wire harness?

Thanks again (OG and contributors) for this thread.
Fish

I would order the C kit with only difference is that it includes a few extra wires which can be used for another future project. No cost savings between the 2.

If you have carbon fiber mirror covers they are just doublefaced tape to the factory covers. So yes just remove the factory cover.

 

[Fish Hunter]

Got it.
So need to remove the Kevlar covers then the OEM mirror covers

Thank you
Fish

Sponsored