2025 DE4 Integra 6 Speed ABP Build

[DE4Willyyyy]

Quiet alright, hope you had a thankfilled Thanksgiving. Also, I have not recieved either part yet. I may return the side one since I don't have a garage or spotter to do what you just described. I did get the main piece which was around $406 USD (Acura Integra High Volume Intake System). Hopefully this won't require any drilling or additional tools besides a socket wrench. Did you remove the resonator? I noticed there was this, did you get the resonator delete?

nope, no resonator delete. only the intake and side duct, nothing else to it.
i think the resonator delete only works for the stock airbox.

Sponsored

 

[wdrx02]

nope, no resonator delete. only the intake and side duct, nothing else to it.
i think the resonator delete only works for the stock airbox.

Great! Was it difficult to replace the O.E intake? Again, I am not planning to install the side duct.

Do you have a picture of your install (engine intake pic)? Would like to get an idea (not of OEM)

 

[wdrx02]

I managed to get the intake installed. However, it was a bit of a pain and unfortunately after the install... I am getting brake failure lights and such (see picture).

(I did connect that map sensor from OE to the new pipping). Do I need to reset anything? I drove it for a few miles and it displayed it throughout. Therefore, I took it easy - although, was able to brake and it seems me sensors does warn me when close to something. I could not turn off the lane assist and such though :/

 

[slowcountry]

Do you have a picture of your install (engine intake pic)? Would like to get an idea (not of OEM)

Similar build

 

[slowcountry]

Any ideas?

Did you plug your air intake sensor back in?

 

[wdrx02]

Here is a shot of the installed:

 

[wdrx02]

Are there any other sensors I should maybe re-plug that deals with what the lights are indicating?

 

[wdrx02]

I notice you have this:

What is that to? I didn't have to remove anything their...I have 24 a Spec (CVT) not ITS. I didn't have to remove whatever that is; as mine doesn't even have what you seem to have.

 

[wdrx02]

I also used this video to install: Youtube install

 

[slowcountry]

That is from the PRL turbo inlet kit - you're not missing it.

You'll need to do a drive cycle to clear those errors - the steps to that should be listed online somewhere. If you have a tuner you can just reflash the tune to skip that. The only time I've gotten those errors is when I either forget to plug in a sensor before I start the car after install, or another time when it went in limp mode because of boost leak.

 

[wdrx02]

That is from the PRL turbo inlet kit - you're not missing it.

You'll need to do a drive cycle to clear those errors - the steps to that should be listed online somewhere. If you have a tuner you can just reflash the tune to skip that.

I do not have a tuner... when you say drive cycle, is that a button to reset with or literally drive a bit? I will google around but if you have a link. Please, could you provide?

 

[wdrx02]

I did find this: how-to-perform-a-basic-drive-cycle. I will check tomorrow morning and let it sit for now.

 

[DE4Willyyyy]

I managed to get the intake installed. However, it was a bit of a pain and unfortunately after the install... I am getting brake failure lights and such (see picture).

(I did connect that map sensor from OE to the new pipping). Do I need to reset anything? I drove it for a few miles and it displayed it throughout. Therefore, I took it easy - although, was able to brake and it seems me sensors does warn me when close to something. I could not turn off the lane assist and such though :/

yeah make sure the sensor is connected properly. that'd be the only thing throwing codes if you installed it properly. I had no codes after install.

Sponsored