Search results

If a 1981 Cadillac can have a memory seat then I am pretty confident our 2024 Integra Type-S can, especially since the position sensors are there. I am doubtful that if we get this working it would work with the fobs and the mirrors, but who knows. I personally would be happy with just the...

It is worth investigating for sure, and I think we are all thinking the same things it may not be possible - but adding what is there: some good signs and some bad. Mix in the aftermarket reading this thread and seeing an opportunity to make a few bucks and we could get more options. Worse case...

The floor wiring is different as well :( I would compare the drivers seat wire harness pins to an a-spec with a type-s. The seats may have the sensors under neath but if the wiring is not there we're stuck.

The front passenger and drivers door wire harnesses are different from the a-spec. and the type-s A-Spec Driver: 32751-3S5-A10 Passenger: 32752-3S5-A10 Type-S Driver: 32751-31M-A00 Passenger: 32752-31M-A00 Not sure what is different with the passenger side, perhaps it is the mirrors...

The question now, is the wire harness there for the seat memory panel behind the door card or did they yank the wiring out to save weight?

They make some micro and mini fuse lead plugs, that be sweet to use here so you do not have to hack up the wiring to add a kill switch. That ghost lock looks like a better approach however than a fuel pump kill switch.

Awesome!!! Summer project!!!

Has anyone figured out how to add front drivers memory seat, or if it is possible? I assume the wiring in the and to the seat is there, we just need the switch and whatever tech built into the seat to make it work, but perhaps I am wrong? I would not need, though it would be nice to have, the...

I couldn't decide where to put this thread, so its in the maintenance section! I wanted to find out what extra steps Type-S owners are doing to protect their investment from theft. My plans for now: Replace the factory wheel locks with more rare aftermarket wheel locks Park in driveway within...

Oh fudge, they are 12 x 1.50. grr!! I pickup my ITS in about 2 weeks.

I test drove a 2023 aspec manual, was ok but it's definitely toned down in comparison to a 2019 Si which I also drive on occasion (my dad's car). I expected the same if not more umph feeling but it wasn't there, you have to really push an aspec to get it to perform. I suspect with some mods voe...

The nut would use a 19mm or 3/4" socket BTW. Dorman part number: 611-150, GM part numbers: 9594683 and 10194314

I set the caliper to 0.68" to show where it falls in the conical area. Here is a photo of 5 in random positions. The black plastic fake nut would then screw onto the lug nut for a cleaner finish, that is what the outer threads between the nut and actual conical end is for, we would have no...

YES! Will post pictures shortly. The conical edge starts at 0.625" and ends at 0.89". Quick math, at 0.68, that is about 20% down from the start of the conical edge. If you look at the tip GM rounded them from the inside thread to the tip, which would give you a little more breathing room if the...

On it, will have some time to caliper the lug nuts tonight, I got a good feeling. Those old factory nuts have the grade 8 steel feel and weight to them, you would need a cobalt or better drill bit to tap them.

@StingertimeNC I have a friend who works at Honda, its hard not to know someone on the Northwest side of Columbus who is not connected to Honda in someway. We have good sushi in Columbus BTW :) I am surprised there is not an annual car show in Marysville for the Honda's/Acura's. Firebirds and...

@Frenzal Thanks! I am going the BMW wheel route, and thanks for the heads up on anchoring it. I am designing a simpler approach that should only require 1 drill hole in the floor for the 8mm buttonhead bolt, though the bolt may need to be 35 or 45mm long. My plan for anchoring is to drill the...

UPDATED: THESE ARE NOT THE CORRECT SIZE LUG NUTS @kjechel on post #37, you said you machined 12mm nuts to 14mm? Where those aluminum lug nuts? Did you try conical seat 14mm steel nuts? Steel on Steel should fair better than steel on aluminum. I have hardened steel lug nuts from my trans am...

You made a good choice. I am waiting for my ITS, 2 weeks ago I put a deposit on one, supposedly today Jan 27th they are starting to build it. Using that site previously linked it looks like there is a severe shortage of blue integra’s, type-s and non type-s. The paint is amazing. I am waiting...

When they stop making this and the CTR that is when you will start to see the resale value stay solid. I suspect we will see a slight rollercoaster at first as some impulse buyers find the car is not for them, after the first few months/years. Only takes a baby - reason I sold my 2007 Si years...