Search results

I got this from Amazon. It was super easy to use, and even came with a clear coat. https://a.co/d/0e3gER6n

Here is an image of when I replaced the center console. It shows you the ziptie that you need to cut. I ended up cutting mine and replacing it with no problem.

I had a buzzing noise coming from the front passenger door. I noticed it between 3,000 and 4,000 RPM with no music playing. If I pressed on either side of the interior door handle, the noise would stop. I removed the door panel and tightened any screws I found on the door and the inner cover. I...

I had a BRZ before my ITS, and it had ANC, which I didn’t like. I disconnected it, and the boxer engine sounded great on its own. I did the same thing with my ITS, but I couldn’t hear any difference whether it was plugged in or not. I tested it in all three driving modes as well. So I did a...

Before I tested it, I checked the seat type with my three favorite AIs, and all three identified it as a ball seat (also known as a radius or spherical seat). Visually, it also looked and felt like a ball seat. The wheel’s ball seat has a very small profile, though, so it was hard to tell. I...

FYI, I tried the OEM lug nuts with the spare T17x4 (42700-TK4-A51), and they worked great. I tightened them down and then removed them to inspect the fit. The studs did not bottom out or contact the back of the lug nuts.

FYI, I tried the OEM lug nuts with the spare T17x4 (42700-TK4-A51), and they worked great. I tightened them down and then removed them to inspect the fit. The studs did not bottom out or contact the back of the lug nuts.

Very nice! It looks flush. Can you let us know your wheel part number and tire size? Also, do you know the part number for the foam insert for the jack and hardware?

It looks like this one does ( 84545-T43-K00 ). It was made to fit a 15 or 16-inch rim. I have decided to go with this wheel (42700-TK4-A51), which has a 17-inch rim. I guess it will fit with some room to spare.

Can you give use the part numbers to the bolts and screws you used? It looks like a clean set up.

I notice this too. I think he had a typo with the part number. It should be 42700-TK4-A51. Look at the image for the correct part number.

Are you saying it is not the tire causing it to go up by an inch, but the inner part of the rim, not the outer part of the rim? For example, where the red arrow is pointing and not in the green area?

Yes, I read your post about the added difficulty and safety concerns of swapping tires in a compromised situation. Fortunately, I live in a fairly rural area, so finding a safe place to pull over and change tires should usually be manageable. You definitely make a valid point about the...

I think you may have that backwards. The 125/80-18 and 125/70-18 are the same width because the “125” is the tire width in millimeters (about 4.92 inches). The second number is the aspect ratio, meaning the sidewall height is a percentage of that width. For your 125/80-18: Sidewall height =...

I did some digging and found a solution. With AI’s help, it looks like these parts should work. The spare wheel is only 4 inches wide and uses a 5x120 bolt pattern with a 64.1 mm hub bore, so the hatch cover should still sit flush. The OEM lug nuts should work as well. The only thing I may do...

I cannot pull up these two numbers. They do not seem to be good numbers. Can you give me a link to search for these parts? 83451-T24-T01ZA - Garnish ASSY., Rear * NH900L * (NH900L Neutral Black) 83406-TVA-A01ZA - Rear outlet Assy (US)

I agree. The ITS is great. I came from a manual Subaru BRZ (Gen 2). It is a light car that is fast in curves. I loved the idea of RWD, but was not one to kick out the tail in fear of wrecking it. This made the ITS a perfect fit for me. The sound system alone is enough to upgrade to the...

I am trying to do the same as TAEGEUK_DE5. I have the Mikstore kit and tried to trim and cut the tabs to work with no luck. The Mikstore tabs are actually too long, but trimming them did not work. Could you give us the part numbers for the Honda rear cover, vent, and small duck to order?

Do you still have this kit, and are you near the Georgia side of North Carolina? How much does the hatchback cover sit up with it stored? Does it fit a front tire location?

Does this spare fit in the front or the rear only, and if it does fit in the front, does the hatch cover sit flush when stored?